Scanning, Inc. Owners of Datalogic products are. Purchaser shall not remov e or alter any proprietar y notices, including cop yr ight. Should future re visions of this manual be published, you can acquire printed v ers ions by contacting your Datalogic rep-. Electronic versions ma y either be downloadab le from the Datalogic website www. If you visit our w ebsite and would like to mak e comment s or suggestions about this.
Datalogic has taken reasonab le measures to provide inf or mation in this manual that is complete and accurate , how-. Datalogic is a registered trademark of Datalogic S. All other brand and produ ct names ref erred to herein may be tr ademarks of their respectiv e owners. Ask a question. Related product manuals. This manual is available in English. No power to the scanEnsure power supply is ner. Interface or power cables are loose. Ensure all cable connections are secure.
Scanner not programmed for correct barcode type. Ensure scanner is programmed to read the type of barcode scanned.
Barcode label is unreadable. Check the label to ensure it is not defaced. Try scanning another barcode type. Distance between scanner and barcode is incorrect. Move scanner closer to or further from the barcode. Barcode reading ability has degraded. Scan Window has become scratched or contaminated with dust. Replace window as instructed in this guide.
Barcode is decoded but not transmitted to the host. Scanner not programmed for the correct host type. Scan the appropriate host type barcode. Laser comes on, but barcode does not decode. The table below defines beep sequences that occur during both normal scanning and while programming the scanner.
Short high beep A barcode label was decoded if decode beeper is enabled. The data is ignored. This occurs if a unit is not properly configured. Check option setting. Parameter Menu Scanning Short high beep Correct entry scanned or correct menu sequence performed. Enter value using barcode keypad. Wait several seconds and scan again. Communication with the bus must be established before the scanner can operate at the highest power level. The power-up beep occurs more than once.
The USB bus may put the scanner in a state where power to the scanner is cycled on and off more than once. This is normal and usually happens when the host PC cold boots. The table below defines LED colors that display during scanning. Green A barcode was successfully decoded. Red A data transmission error or scanner malfunction occurred. Some frequently used programming barcodes are also included. For all programming barcodes, plus detailed information about the scanner, download the latest version of the Product Reference Guide PRG , Advanced Data Formatting ADF Guide and all documentation pertaining to the scanner from the website listed on the back cover of this manual.
The definitions that follow briefly explain the programming barcodes. Set Defaults Scan Set Defaults to set all parameters to their default values. Host Interfaces Cables may vary depending upon system configuration.
No additional power supply is required. Please refer to the PRG, downloadable from the website located on the back cover of this manual. Regulatory Information All models are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.
Any changes or modifications to equipment, not expressly approved by Datalogic could void the user's authority to operate the equipment. Power Supply Use only a power supply approved by Datalogic for this product and model. Input: - VAC Output: 5. Eingang: - VAC Ausgang: 5. Strom: 0. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
However there is no guarantee that interference will not occur in a particular installation. The laser classification is marked on one of the labels on the device. The following statement is required to comply with US and international regulations: Use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous laser light CAUTION exposure. Class 2 laser scanners use a low power, visible light diode.
As with any very bright light source, such as the sun, the user should avoid staring directly into the light beam. Momentary exposure to a Class 2 laser is not known to be harmful. Replacing the Scan Window If the Scan Window becomes scratched, broken or contaminated with heavy dust, replace it by removing the Nose Boot and installing a new window. Datalogic offers a replacement window as an orderable accessory. Gently pull off the Nose Boot and tilt the scanner to one side to remove the window.
Proceed to the next step immediately. DO NOT leave the interior of the scanner exposed. Scanner Labeling Labels are shown here to illustrate their location only. Please view the labels on your product for actual details. Italian Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.
Class 1 or Class 2 products are not considered to be hazardous. The scanner contains internally a Visible Laser Diode VLD whose emissions do not exceed the maximum limits as set forth in the above regulations. The scanner is designed so that there is no human access to harmful laser light during normal operation, user maintenance or during prescribed service operations.
Opening or servicing any part of the optics cavity by unauthorized personnel may violate laser safety regulations. The optics system is a factory only repair item. Optical systems include binoculars, microscopes and magnifying glasses. This does not include eye glasses worn by the user. Das Optiksystem darf nur werkseitig repariert werden. I prodotti di Classe 1 o Classe 2 non sono considerati pericolosi.
Lo scanner contiene al suo interno un Visible Laser Diode VLD , diodo laser visibile, le cui emissioni non eccedono i limiti stabiliti dalle normative sunnominate. Sistemi ottici includono cannocchiali, microscopi e lenti di ingrandimento. Optiske systemer omfatter kikkerter, mikroskoper og lupper.
Det omfatter ikke anvendelse af almindelige briller. Dutch Deze scanner is in de V. Producten van klasse 1 Class 1 en klasse 2 Class 2 worden niet geacht gevaarlijk te zijn.
0コメント